0

My Cart

0
Subtotal: $0

No products in the cart.

No products in the cart.

0

My Cart

0
Subtotal: $0

No products in the cart.

No products in the cart.

How do I calculate the correct panel sizes and gaps for my fence run?

Calculating your glass panel sizes and gaps requires precision down to the millimetre. Because toughened safety glass cannot be cut or altered once it leaves the factory, getting your maths right before ordering is critical to passing your AS 1926.1 inspection.

The step-by-step process to plan a flawless, uniform layout is detailed below:

Step 1: Understand Your Legal & Practical Constraints

Before running any maths, you must factor in the strict spacing boundaries required for compliance and hardware installation:

  • The Legal Gap Limit: Under Australian Standard AS 1926.1, the gap between consecutive glass panels must never exceed 100mm.
  • The Industry Sweet Spot: For a clean, architectural finish, the industry standard gap is between 20mm and 60mm. Most professional installers aim for a crisp 30mm or 40mm gap.
  • The Gate Kit Clearances: Your gate is a fixed structural unit and cannot be customised. A standard glass pool gate is typically 900mm wide and requires a precise 8mm to 12mm gap on the hinge side and the latch side for the magnetic safety mechanisms to strike correctly.

Step 2: Calculate Your Net Install Length

To find out how much space you actually have for your fixed glass panels, you must subtract your gate assembly from the total boundary run.

  • Measure the Total Boundary Length in millimetres (from wall to wall, or post to post).
  • Subtract the Gate Width (typically 900mm).
  • Subtract the Gate Hardware Gaps (typically 20mm total — 10mm for the hinge side and 10mm for the latch side).
  • The remaining figure is your Net Fixed Glass Length.

Example: If your total fence run is exactly 5000mm:

5000mm − 900mm − 20mm = 4080mm

Net Fixed Glass Length: 4080mm

Step 3: Determine the Number of Panels & Gaps

To maintain a high-end, premium aesthetic, you should try to use panels of equal or highly similar widths across your straight run rather than mixing huge 1800mm panels with tiny 300mm panels.

  • Divide your Net Fixed Glass Length by a standard mid-sized modular panel width, such as 1200mm, to get a rough estimate of how many panels you need.
  • Count your gaps: The number of internal gaps between your fixed panels will always be the number of panels minus one, assuming the end panels sit tight against a wall or post.

Example (continuing from above):

  • 4080mm ÷ 1200mm = 3.4 panels. Round this up to 4 panels.
  • 4 panels means you will have exactly 3 internal gaps between them.

Step 4: The Final Maths Adjustment

Now, choose your desired standard gap size, for example 40mm, and subtract that total gap space from your net length to pinpoint your exact panel widths.

  • Multiply your chosen gap size by the number of gaps: 3 × 40mm = 120mm of total gap space.
  • Subtract the total gap space from your net length: 4080mm − 120mm = 3960mm of pure glass width.
  • Divide that pure glass figure by your number of panels: 3960mm ÷ 4 = 990mm.

Your Final Order: You would order exactly 4 standard panels at 990mm wide each, and space them with uniform 40mm gaps to complete a flawless 5-metre run.

📋 Custom Workarounds for Awkward Dimensions

Backyards rarely divide into perfect, neat fractions. If your maths results in a non-standard glass size, such as 1132mm, use these trade strategies to avoid paying premium prices for custom factory cutting:

  • Round to the Nearest 50mm Inventory Line: Standard warehouse panels from DIY Frameless Glass are stocked in clean 50mm increments, such as 1100mm, 1150mm and 1200mm.
  • Absorb the Difference in the Gaps: If your ideal size is 1132mm, buy the stock 1150mm panels and reduce your gap sizes by a few millimetres, or buy the 1100mm panels and increase the gaps slightly, while keeping them safely under the 100mm compliance ceiling.
  • The “Make-Up Panel” Trick: If you have a long run, buy identical large modular panels, such as 1500mm panels, for the main section, then place a single smaller panel, often called a “make-up panel” or filler pane, at one end near a garden bed or wall to absorb the remaining measurement.

Leave a Reply

Scroll to Top

Filter Categories

Categories

IMPORTANT INFORMATION FOR CHRISTMAS BREAK

Christmas 2026 Closure Dates

We wish to advise our annual Christmas holiday closure from 12pm Wednesday 23rd December, 2026. Phones and emails will not be answered during this period. We will resume normal trading hours on Monday 11th January, 2027.

Please note 2026 order cut-off dates:

  1. Local delivery booking & custom glass orders: 20th November
  2. Crate, skid & palletised orders: 27th November (please note: pre-Christmas crate delivery is not guaranteed, due to potential delays with transport companies)
  3. Postage & courier orders: 14th December
  4. Pickup from warehouse: before 2.45pm, Tuesday 22nd December.
  5. Online orders placed after 18th December may not be processed until 12th January 2027

To ensure dispatch prior to the holiday closure, orders must be received and paid/confirmed by close of business on these dates.

As at 6th November 2026, all new and current orders are subject to capacity and/or stock allocation.

Thank you for your valued business and we wish you a safe and merry Christmas.